Inflatable 250T/M Air Lift 0.08mpa Marine Rubber Airbag
►Marine Rubber Airbag introduction
Inflatable Air Bags for shipping is China independent intellectual property rights of innovative
products, the products are mainly applied to ship launching and
landing, weight lifting, handling, installation of underwater
buoyancy aid etc. Nowadays, inflatable air bags for shipping are widely used in the world. The Products are less limited by
space, no large mechanical equipment, can shorten the working
period and save the unnecessary cost. Through years of development
practice, pneumatic air bags is become more safety, effective and green environmental
protection.
Whole Intertwine Technology
"Henger" inflatable air bags for shipping overall frame structure uses cross whole intertwine technology, the
overall structure is more reasonable, texture clear, no juncture,
high loads, more safety than lap technology (roller), more than 20%
bearing capacity.
►Product Advantage
Inflatable rubber airbag’s main technical requirement is regulated
in CB/T 3795--1996 published by China State Shipbuilding
Corporation.
Henger adopts new rubber formula and high-strength enhanced
synthetic-tyre-cord layer, which improves the airbag’s bearing
capacity two times more than CB/T 3795--1996 standard.
The synthetic-tyre-cord layer of Henger marine airbag adopts dipped
Nylon-6 1400dtex/3-V2 tyre cord.
The strength & durability of airbag improves 20%, compared to
polyester tire cord which is widely used by friendly competitors
- High Kneading-resistance Capability
When the airbag is rolling under the ship bottom, it will suffer a
“kneading force” from ship bottom and ground because of not uniform
rolling speed, which could case problems like delamination, layer
buckling, etc.
Henger improved the manufacturing technique and raw material
formula to strengthen kneading-resistance capability of the airbag
and avoid worse accident .
Each layers of airbag are painting with specially formulated
mucilage to dissolve dust & impurities.
The specially formulated mucilage
also higher the adhesiveness among each layers to guarantee the air
tightness.
While most of friendly competitors cut this process in production
to save manufacturing cost.
- New Anti-explosion Design of End Part
The possibility of air leakage in the joint area of metal part and
rubber part is also increasing as working pressure of airbag is
added. After using for times under high working pressure, the
airbag would burst and metal part would hurt workers.
Henger invented new anti-explosion design of the airbag end part,
increasing the bonding strength and air tightness between rubber
body part and end metal part. Henger airbag is working very well
under higher working pressure without potential safety hazard.
- High strength galvanized anti-release structure
casting metal part with chemlok coating.
chemlok coating strengthens the bonding between metal part and
rubber body after vulcanization.anti-release structure of the metal
part makes the connection more tight.
- Optimizing Structure Configuration
Henger built a strength and intensity model to test compression
performance, stress intensity and direction. After testing for many
times, we got the stress changeing regularity and optimized structure configuration design. The new optimized
airbag successfully passed blasting experiment and achieved good
performance in practical use.
Hydraulic Blasting Test is an all-around ultimate test for the
performance, material, structure design, manufacturing technique of
marine airbags.
The testing result of Henger Marine Airbag is beyond industrial
standard
Hydraulic blasting test for Henger marine airbags Inspected by
American customer and third-party detection institution
- Good Abrasion-resistance Performance and High Ageing Resistance
The airbag is working under bad and poor condition, suffering from
long time sunlight exposure, seawater impurities pollution, etc.
The surface of airbag must be equipped with high capability of
abrasion resistance, ageing resistance, corrosion resistance.
Henger airbag is made of natural rubber with special ingredients
and unique manufacturing method. The finished airbag could working
very well under above mentioned bad and poor working condition.
- Higher Flexibility and Shock Absorption Capability
Henger airbag is manufactured with unique integral twining technique. The airbag wall thickness is uniform with secondary seam in
overlap joint. When rolling in slope and uneven ship path, the
flexible airbag is helpful to reduce structure stress and ship
launching risk.
Heavy distortion phenomenon would cause delamination among airbag
layers, then to cause more serious accidents.
Such dangerous distortion phenomenon in ship launching process
never happened to Henger Marine Airbags
►Company introduction
Qingdao Henger Shipping Supplies Co., Ltd
Lies in Qingdao, a beautiful coastal city with red tiling and green
trees, blue sea and clear sky, Qingdao Henger Shipping Supplies
Co., Ltd is a high-tech enterprise integrated with manufacturing,
research and innovation, technical services, specialized in
manufacturing marine products, such as marine rubber fender,
, navigation mark and marine buoy. All products get ISO 9001-2008
certificate and IACS quality authentication from CCS, BV, GL, ABS,
LG, etc. With strong technology base, advanced manufacturing
technique, complete manufacturing facilities and well-equipped
checkout equipment, Qingdao Henger Marine Supplies Co., Ltd is
devoted to forge itself into a top-ranking international
competitive marine products manufacturer providing high quality
products and perfect service for all customers, and shoulder the
responsibility of ensuring global marine safety via mutually
beneficial cooperation with friends all over the world.
